產品介紹：
·該鋸適用于危險的工作環境，可在較高溫的環境下作業，無火花，在潮濕的環境中無漏電危險，是一款性能可靠、安全型及效率極高的理想風動工具之一。廣泛用于采礦、石化、建筑等行業。
·利用井下壓風管道系統作為動力源。重量輕，易攜帶；結構科學，便于作業。
·可快速切割管道、電纜、角鋼、結構鋼、U型鋼、鏈條、錨桿、錨索等。
·錮金屬鋼合金超級鋸條，耐高溫、耐摩擦、使用壽命長。非常適用于鋸割不銹鋼、鎳基合金、鐵、銅、鋁、玻璃、塑料、木材等。技術參數：
遼寧撫順市礦用U型鋼切割鋸手持式FDJ-230型大行程氣動無火花切割鋸廠家
聯系人金經理電話13934240041
微信號13934240041
|
型號
|
功率
|
耗氣量
|
|
切割寬度（直徑）
|
鋸片速度
|
重量
|
|
WZJ-120
|
0.5kw
|
0.6
|
|
120mm
|
60m/min
|
6kg
|
1、了解所需切割的材料，如有必要可以通過降低空氣壓力來降低鋸片的轉動速度。
2、確保牢固固定了所需切割的材料，防止其移動。
3、氣動空氣馬達時，用手指按壓閥桿，然后開始切割。
4、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命。（注意：避開切割后可能掉落的碎片。切割即將完成時，切勿使鋸碰到您的身體、工件或附近的其它人員。）
5、關閉空氣馬達時，釋放閥桿。
6、下次切割開始前，鋸片必須保持運動狀態。氣動鋸時，鋸片不能接觸任何表面。
7、斷開空氣軟管時，關閉空氣軟管閥。斷開前，先打開空氣閥給軟管減壓。
8、更換鋸片前，務必斷開空氣軟管，并推動閥桿以釋放掉馬達內的壓力。
9、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。
遼寧撫順市礦用U型鋼切割鋸手持式FDJ-230型大行程氣動無火花切割鋸廠家
聯系人金經理電話13934240041
微信號13934240041
FDJ-120 pneumatic cutting saw use method:
1. Understand the material that needs to be cut, such as the reduction of air pressure to reduce the rolling speed of the saw blade. Cutting and sawing Ningxia high quality with mining bolt and anchor cable
2, ensure the sturdy fixation of the required open data to avoid its movement.
3. When pneumatic air motor, press the stem with the finger, and begin to cut.
4, use the component of the saw to control the cut pressure. For the softer data, this component has been satisfied. Too much pressure will reduce the speed of the saw blade. With more hard data, the rolling speed of the saw blade can be reduced by a pressurized method. The incision is to stick to the saw vertical. Any distortion or tilt of the saw may decrease its service life. (notice: avoid fragments that may fall after a cut. Do not make the saw touch your body, the workpiece, or the other people in the neighborhood when the cut will be finished.
5. When the air motor is closed, the stem is released.
6. Before the next opening, it is necessary to adhere to the movement of the saw blade. When a pneumatic saw, a saw can't touch any appearance.
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.
8. Before replacing the saw, it is necessary to disconnect the air hose and push the stem to release the pressure of Madane.
9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod.
