山東 Ssz –1400 自動走礦山采石機

Ssz –1400 自動走礦山采石機

濟寧八方礦山機械有限公司

Jining bafang Mining Machinery Co.,Ltd

應用于礦山荒料采石場、路面切割等硬物料切割之用

Used in mining Huangliao quarry, road cutting and other hard materials for cutting purposes4、 確保水管通水后再啟動鋸片下降，開始切割．在切割過程中，確保鋸片處時刻保持通水。

Ensure that the water pipe and then start the blade down, start cutting. During the cutting process, ensure that the saw blade at all times to maintain water

5、 在鋸片向下切割時，要密切注意切割深度；深度不得超過電機的負荷；一般切割深度由石材的硬度來確定，切勿急于求成；高深度的切割可作２－３次切割分次完成．達到一定深度后，再開啟行走開關，自動行走切割。

The depth of the cutting should not exceed the motor load; general cutting depth to determine the hardness of the stone, not anxious for; high-depth cutting can be used for 2-3 times the cutting fractionation carry out. Reach a certain depth, and then open the walk switch, automatic walking cutting.

6、 切割完成停機時，先將行走關停后，刀盤空轉幾秒不再切割后，再關閉主機電源。

cutting to complete shutdown, the first stop after the walk, the cutter blade idle after a few seconds no longer cut, and then turn off the host power.

◆安全須知

Safety instructions

切割時勿必保持供水、供電線路正常，操作員離主機一定距離。Do not cut the water supply, the power supply line is normal, the operator from the host a certain distance.

◆本款自動行走，行走速度快慢可調，鋸片自動升降

This section automatically walks, walking speed adjustable speed, automatic saw blade movements

◆全套包括 Full set included    ◇主機main machine
               ◇￠1400mm鋸片X 1400mm saw blade X1
               ◇軌道10米 （三根可交替使用）Track 10 meters (three can be used interchangeably)
               ◇主電動機一個 行走電機一個The main motor a walking motor

◆本廠生產的礦山采石機，機子小巧靈活、移動方便、價格低、功能大。適用于小規模高效率開采石材，大型礦山開采小塊荒料使用，可廣泛地應用在凝灰?guī)r，花崗石，大理石礦山切割開采。目前已經在浙江，安微，等華東地區普遍應用。

◆以我們本地凝灰?guī)r為例，石質稍軟，一天8小時可切

割凝灰?guī)r150米。工作效率高，石材出產率高，電耗省。

◆工作原理：以電動機或柴油機為動力帶動主機鋸片高速旋轉，切入巖石，并運用小電動機沿軌道推行，結合鋪助設備實現了無爆破和無熱切割的嶄新石材荒料開采工藝

◆技術參數

◇可切山體深度： 550mm     

◇可切長度/寬度：不限,可自定

◇主電機：  功率22kw  

◇行走電機：功率0.55-0.75KW  

◇主軸轉速：800 ~1000/分鐘   

◇主機重量:610KG

◇耗水量: 3m3/h (水量要求能潤滑鋸片，降溫，除塵)

◇總重量: 1100KG

◇ Cutting depth: 550mm

Can be cut length / width: unlimited, can be customized

◇ main motor: power 22kw

◇ Walking motor: power 0.55-0.75KW

◇ Spindle speed: 800 ~ 1000 / min

◇ host weight: 610KG

◇ Water consumption: 3m3 / h (water requirements to lubricate the saw blade, cooling, dust)

Total weight: 1100KG

◆安裝與使用：

1、安裝護水蓋，對準護水蓋的安裝口，再鎖緊螺母。(保持護水蓋與主機程垂直，以免鋸片切到護水蓋)。

2、 安裝鋸片：先將主軸升地面，高度大于鋸片的半徑以上，再松出主軸上的鎖緊螺母，取出外夾片；內夾片的正反面有兩個不同大小的凸臺，選擇與鋸片內孔大小相配的一面并朝外。使鋸片孔與內夾片的凸臺緊密配合，再按上外夾片，鎖緊螺母。（注金剛石刀盤要與軌道程平行狀態，在出廠時我廠方已調節過，可作為參考）。

3、打開減速機蓋，加入清潔機機油（請勿必加油后使用）。

   注：出廠時機油已加，注意定期檢查。

4、 鋸片升降絲桿，加入清潔機油。(注:每個工作班需加油1～2次)

5、 接入主機電源線：三廂四線。接線方法，接線頭已在配電箱中接好。打開配電箱，再把所留的電源線去掉，改換成16平方的電源線，并在相應的接線柱上接上電線；黃色的為零線，不需要拆，只要接上相應的延線即可。

1, the installation of water protection cover, aligned water cover installation mouth, and then lock nut. (Maintain the water cover and the main vertical process, so as not to cut blade to protect the water cover).

2, the installation of saw blade: first spindle up the ground, the height is greater than the radius of the blade above, and then loosen the spindle lock nut, remove the outer clip; Select the side that matches the size of the hole in the blade and faces outward. So that the blade hole and the clip inside the boss closely, and then on the outer clip, lock nut. (Note that the diamond cutter with orbital parallel to the state, the factory I have been adjusted when the factory can be used as a reference).

3, open the reducer cover, adding cleaning machine oil (do not use after refueling).

   Note: The factory oil has been added, pay attention to regular inspection.

4, saw blade lift screw, add clean oil. (Note: Each work class to refuel 1 or 2 times)

5, access to the host power cord: three four lines. Wiring method, wiring head has been connected in the distribution box. Open the power distribution box, then leave the power cord removed, replaced by 16 square power cord, and in the corresponding terminal on the wire; yellow for the zero line, do not need to split, as long as connected to the corresponding extension Line can be

注：線接好后檢查一下上升與下降，如相反，進線的任兩個線頭對換就行。

6、接好進水管，以保證工作時供水充足。

7、全面檢查主機，在各部件滑動處定時加機油。

◆操作使用方法

1、 安裝各部分完成后，帶好防護手套。鋪好軌道，軌道有專用的接頭，軌道用木塊基本墊平固定，把主機置于軌道上。

2、 檢查行走四輪是否正確架于軌道上，如有輪子懸空的，調整軌道高低至接觸。

3、 手動轉動鋸片，檢查鋸片是否與軌道平行，檢查鋸片是否正常運轉，并依次檢驗操作面板上的按扭是否正常。

Note: Check the line connected to the rise and fall, such as the contrary, the line of any two thread on the line.

6, connected to the water pipe, to ensure adequate water supply at work.

7, a comprehensive inspection of the host, in the sliding parts of the regular increase in oil.

◆ operation to use

1, after the completion of the installation of various parts, with a good protective gloves. Paved track, the track has a dedicated connector, track the basic block with a fixed block of wood, the host placed in orbit.

2, check whether the correct four-wheeled track in the track, if the wheels are vacant, adjust the orbital level to contact.

3, manually rotating blade, check the blade is parallel with the track, check whether the normal operation of the blade, and in turn check the buttons on the operation panel is normal.